SureMAX Импланти сутунмуҳраи гарданӣ аз Additive Implants Inc.

Тарҳи SureMAX Импланти сутунмуҳраи гарданӣ аз Additive Implants Inc. ғолиби шоистаи ҷоизаи бонуфузи 2020 Ҷоизаи биринҷии A' Design Award дар категорияи мусобиқавии Дизайни дастгоҳҳо ва таҷҳизоти тиббӣ мебошад.

БиринҷМаҳсулоти тиббӣ· 2020

SureMAX Импланти сутунмуҳраи гарданӣ

аз ҷониби Additive Implants Inc.

Муштарӣ: Additive Implants Inc

Ғолиби Ҷоизаи биринҷии A' Design Award дар категорияи Маҳсулоти тиббӣ

18,477

Ғолиби тасдиқшудаи ҷоиза

Тасдиқи вазъи ҷоиза барои #88502

Ба сайт гузаред Дар A' Design Award дидан Релизи матбуотӣ Нишони ҷоиза

Рангҳо

Тарҳ

Дар бораи SureMAX Импланти сутунмуҳраи гарданӣ

SureMAX як импланти титанӣ барои сутунмуҳраи гарданӣ мебошад, ки дар ҷарроҳии дискектомия ва фузияи пеши гарданӣ истифода мешавад. Сахтии SureMAX ба сахтии устухони бемор мутобиқ карда шудааст, аз ин рӯ мӯҳра осеб намебинад ва имплант фуру намеравад. Устухон ба титан хуб мерушад, аммо қафасҳои титании пештара хеле сахт буданд. SureMAX бо усули чопи сеченака аз хокаи титан истеҳсол мешавад, ки имкон медиҳад шаклҳое сохта шаванд, ки бо коркарди механикӣ ба даст оварда намешаванд. Сатҳи он сӯрохидор ва бӯғноковашуда сохта шудааст, то рушди устухонро дастгирӣ кунад. Тирезаҳои паҳлуӣ имкон медиҳанд, ки шифоёбӣ дар тасвирҳои рентгенӣ дида шавад.

Эътироф

Дар бораи Ҷоизаи биринҷии A' Design Award

SureMAX Импланти сутунмуҳраи гарданӣ ғолиби Ҷоизаи биринҷии A' Design Award аст, ки эътирофи басо обрӯманд буда, ба тарҳҳои барҷаста дода мешавад, ки бо эҷодкорӣ, зеҳни тез ва зиракӣ фарқ мекунанд. Ғолибони биринҷ артефактҳои хеле моҳир ва ба таври ҷолиб эҷодкоронаанд, ки таҷрибаи васеъ, тасаввурот ва зеҳни тарроҳони худро тасдиқ мекунанд. Интизор меравад, ки SureMAX Импланти сутунмуҳраи гарданӣ ашёи хеле қадршуда, мавриди таҳсин ва маҳбуб бошад, ки ба таври назаррас касбӣ ва навоварона аст. Ин тарҳи ғолиби Ҷоизаи биринҷии A' Design Award беҳтарин амалияро дар санъат, илм, тарроҳӣ ва технология дар бар мегирад ва бо диққати худ ба тафсилот аъло аст. SureMAX Импланти сутунмуҳраи гарданӣ эҳтиёҷотро бо зебоӣ қонеъ мекунад, ба хостаҳо даст мерасонад, эҳсосотро мафтун месозад ва кунҷковиро ҷалб мекунад.

Дар паси тарҳ

Маҷмӯаи матбуотӣ

Кредитҳо, аъзои гурӯҳ ва тафсилоти техникие, ки тарроҳ пешниҳод кардааст.

Хусусиятҳои беназир: SureMAX is the first Titanium spinal implant that has a stiffness that matches the individual's bone stiffness as not to damage it. Bone loves to grow into Titanium but Titanium cages have been limited because they are too stiff and damage the bone. SureMAX has solved this problem through using 3D print technology with geometries that are not machinable. It also has a porous roughen surface to encourage bone to grow into it.
Андоза ва бастабандӣ: There are 72 sizes for SureMAX. The height, the foot print and the angle of the implant are the 3 choices. The angles are 0, 7 and 14 degrees. The choice of the angle is used to correct any stenosis in the spine (this is when the spine has a deformity and the implant is used to fix it). The heights are 5,6,7,8,9,10,11 and 12 mm. The foot prints are 12x14 mm, 14x16 mm and 15x118mm. All units come in a sterile plastic package.
Тегҳо: spinal implant, Inter body fusion device, IBFD, cage, Titanium, Ti Cage, 3D printed, Spine
Технологияи истеҳсол: 3D print technology has been used with Titanium powder (Ti6Al4) using porous surface technology to achieve designs that will encourage bone to grow into the spinal implant
Мушкилоти дизайн: To get result required- a high performance implants which is cost competitive, the team had to design a part that could both hand the stresses and forces required by the US government FDA while solving the patient challenges. The part had to be designed so minimal post processing would be required after 3D printing. Additionally, the rough porous surface which helps the healing process required advance software and new methodologies to manufacture. The diving boards had to share the spinal loads equally in order not to displace the implant in the spine. Side windows had to be designed that permits the loads to be distributed and have large have enough surface to see the bone healing. The hardest part of the design activity was to figure out how 8 independent platforms on both sides of the implant could function as a single unit and share the loads appropriately. The surface had to be porous and roughened Ti that could handle the appropriate loads. The teeth had to be the correct size and angle in order to assure stability, but not too big or small to them a ineffective.
Таҳқиқот: Titanium (Ti) has always been the material of choice for implants. But Ti is hard to machine and is very stiff. In the interface between Ti and bone, bone can be damaged and the implant subside ( or settle ) in the body. Plastic and Allograft bone material implants are used to address Ti's limitations. Additional, Ti is not X-ray translucent, so physicians can not see how the bone heals through and around the implant. Plastic implants also have the limitation that they remain inert in the body- they are never adsorbed. Bone however grows very well into Ti. The challenge was to create a Ti spinal cervical implant (cervical is for the neck) that had the same stiffness as bone as not to damage it, would not subside (it would stay on top of the bone and not settle), would remain in the position inserted (with the neck movement would not slip), X-ray could go through it (healing could be observed), would pass the stress test required by the FDA and would be cost effective.
Илҳом: The inspiration was the lack of a solution that took advantage of new geometries that can be created with Titanium which is the best material for bone to grow into by a spine surgeon who performs over 300 cervical surgeries a year. He wanted an implant made from Titanium that matched bone's hardness, not to damage the vertebra, was visible in X-rays, so healing could be seen through, and would not subside in the spine.
Давомнокии лоиҳа: The design started in 2015 and ended in October 2018 and FDA approval was received in February 2019 (3 year design and 4 month approval). The work was done in Phoenix Arizona USA.
Ҷараёни кор: The implant is used in an Anterior Cervical Discectomy Fusion (ACDF) surgery where the front of the neck is opened, the damaged cartilage removed and an implant is inserted in order to fuse the vertebra. The implant comes in a sterile plastic package. The surgeon once the damage is observed and removed assesses the size required. The appropriate implant size, angle and foot print is selected and inserted into the spine. A plate is then used (not part of SureMAX) to attach the upper and lower vertebra. The bone then grows into the implant (called inter body fusion device IBFD) and the patient heals.
Патентҳо: Patented #10,299,938 Additive Implants Inc., May 2019, USA
5 additional patent pending and provisional patents
FDA #K182477 (2019), holder Additive Implants Inc. USA
Trademark #88115736 (2018), Additive Implants Inc. USA
Аъзои гурӯҳ: Dr. John Ehteshami MD
Robert Brosnehan
Matt Zoghi
JD Howell
Jeff Horn
Babak Ehteshami